How to set up VXDIAG Porsche PIWIS3 VCX DoIP WiFi connection

Question:
I cannot mange to setup wireless connection between vxdiag vcx doip Porsche Piwis 3 and laptop. How can i enable wifi connection? How to search WLAN and set up IP address?

Solution:
Porsche PIWIS3 Wifi setting is the same as VXDIAG Porsche PIWIS2
How to set up/connect VXDIAG Porsche PIWIS2 VCX Plus with laptop via WiFi?
1.Click [SETTINGS]->[Network settings]


2.Click [WLAN]，then Select a network card

3.Click [Search]，then click select Network name，and input Network Key
4.obtain ip address automatically：select [Obtain IP address automatically] and [Obtain DNS server address automatically],then click [Save]

5.Manually settings IP address : select [Use following IP addresses] and [Use following DNS server addresses],then input IP address 、subnet mask 、standard gateway 、Preferred DNS Server , then click [Save]

05.2019 Lonsdor K518SK518ISE Feedback Tested on EUUS vehicles

(05.2019) Have collected some new test reports of Lonsdor K518S/K518ISE .
The tests… Here you go
Alfa Romeo 147 1.9JTD
2007
Program key OK
Program remote OK
BCM Marelli

Citroen C3 1.6hdi
Year 2016
Read pin type1 OK
Programming key OK
BSI Johnson Controls

Insignia 2012
Read pin Ok
Add key OK

Hummer H3
Made remote OK
Original key is without transponder.
Remote generated with KD – brand GMC 315Mhz.
Open, Close and Panic buttons are work.
Well done.

Kia Carens 2013
keyless add 1 minute
Peugeot 508 pin Type 1 key programming via model OK

Range Rover Evoque 2014
all keys lost with lonsdor OK
lonsdor-k518-Range-Rover
HYUNDAI TUCSON 2016
Program Keyless HITAG 3- OK!!!
Pincode from service.

Fiat Scudo
made by menu Citro?n type II
and before read PIN – Citro?n type I.
KD key all works.

Corolla id 67 good
Mondeo 2014 6e80 security Access failed, done with mvp

CITROEN DS5 2012 SMART KEY ID46
PIN AND KEY PROGRAMING
10 MIN

RENAULT LAGUNA III 2009
Program card – OK!!!


Mazda 3 2016 usa – no problem – done


Mustang 2016
proxy key with lonsdor 30 sec

Hyundai Santa Fe 2016 smart key
Key programming ok
Pin from service..

CITROEN C4
Read pin OK
Program immo OK
Program Remote OK
Pin Read by car, immo
and Remote by type… don’t remember witch type but success

Mazda cx7 2007 programming

Peugeot 206.
2002 year id 46 pin read ok
key programming failed
Key add with other device


Renault Kangoo 2009.
When i select Kangoo – faild.
Then I select Trafi? Ph3 – everything ok.


Peugeot Boxer 2018
3 min job

VW Caddy II 2009
Backup EEPROM
Read Immo data
Make dealer key
Learn key FAILED
It wrote timeout error.
But than comlepte with another device so dealer key was made right on Lonsdor.
lonsdor-k518-VW-Caddy
Nissan NV400 2012 done (Master III 7947)

lonsdor-k518-Nissan-NV400-2
Corsa E 2016 Done

Renault Mascott add key

Seat Leon FR 2017 MQB
off-line,
vw immo4, mqb,
backup immo data,
make dealer key,
programm key.
3-4 min. done!
(all vw seat skoda after 2013-14 is this mqb type)


2006 Opel vivaro key programming

Again, thanks to all users with Auto Key Programmer Lonsdor k518
It’s kind of you to share all the test report with all

---

How to use CGDI BMW to do Cas3+ all key lost

We listed the steps here for how to use CGDI BMW Programmer to do all key lost programming for BMW CAS3+.
Tools you need:
CGDI BMW MSV80 Programmer
CG100 PROG III
Procedures:
Step 1:Read ECU EEPROM
Run CG100 software,enter menu to select “ECU”

Select “BMW E Series and then MEVD1724(N20)

After then CG100 software will show the wire connection diagram as below,you need to build the connection according to the diagram.


Click “Read EEPROM”

After data reading successfully,save the EEPROM data on your laptop.

Now you can see the ISN and VIN here:

Step 2:CGDI BMW Programming Key
Connect CGDI BMW Programmer to vehicle by OBD port,then select “BMW OBD Key Match”

Click “Read Key info”

Pull out the key from the ignition when it prompt you as below massage

Then save the data file

Select the key position to program and then click “Generate dealer key ” to continue

Now,here it will prompt you to enter ISN
Select “have engine data,the next step will load the engine data”

Load the engine data read out the CG100 in step 1

Put the new blank key into the CGDI BMW coil,then click “OK” to continue

It will prompt you that “Whether the key currently programmed is a smart key”
Note:If it is a smart key,the key will be locked.
Click “No” to continue

Wait a second minute,it will show the programming key was successfully

After learning,it can be used normally.

Now buy CGDI Prog BMW MSV80 Car Key Programmer with Full Authorizations Get 8 Foot Chip Adapter for free. USD539 free shipping.