Launch X431 Pro Mini do VW Jetta 2014 P0106 P3078

Launch X431 Pro Mini customer share:
Tested it on a 2014 VW Jetta, diagnose full system, read clear engine DTC codes P0106 P3078. Launch X431 pro mini diagnose American, European and Asian cars!

Already diagnosed many cars by Launch X431 Pro Mini Bluetooth, easy to do!
This time I diagnosed VW Jetta all systems and cleared engine DTC codes, so car back to normal.
Steps:
Go to Europe tab and select VW to start.

Open Launch X431 software VW V27.80.
Choose System Selection and select 01 Engine Electronics


It show me ECU information and car VIN. It’s helpful!

Then directly go to 02 Read DTC.

Launch X431 Pro Mini read Jetta engine DTC fault codes successfully!
VW DTC P0106 P3018 and description.

Press the Search icon at right side, I can also google the DTC codes.

Last step is back to 01 Engine Electronics menu, choose 05 Clear Fault Memory and all DTC codes disappear!
Easy and pleasant VW Jetta troubleshoot& Launch X431 Pro Mini

And also share helpful information below!
Launch X431 Pro Mini user manual download:
How to register and activate Launch X431 Pro Mini?
http://forobd2tool.com/wp-content/download/Launch-X431-Pro-Mini/launch-x431-pro-mini-bluetooth-user-maunal.pdf
Launch X431 Pro Mini quick start: Zoom to check more

Can I use Tech 2 for OBD1

TECH 2 scan tools work with GMs from 1991- 2013
OBD1 is everything before ’96!
If the menu is in the Tech2 for ’91 then that hints that all you would need is the correct 16 – 12 connector/adapter and also likely a provision to power it with the adapter. OBD2 is self-powered from the DLC, OBD1 ain’t. ’94 & ’95 would work without the adapter, they’re 16 pin DLC with pin 16 being B+.
I’ve used my “REAL” Tech 2 Scan Tool with ’95 but not Corvette, compared to my Tech1 on the same car I did have some contradictory comparisons that I couldn’t explain. I don’t recall them now but it did confuse me for a time. I put a JY ECM in a ’95 ParkAvenue for a fellow to resale and it ran well so I worried NOT about it.
FYI, There is a Tech1A OBD1 to OBD2 interface that lets the Tech1a work fine with 96.
I have done it multiple times, you MUST have a Tech1A with correct mass storage module to install a new PCM or CCM to program key fob resistance, mileage , vin info ,LT1 or LT5. You have 100 miles after install to program the module or it becomes non programmable. (this pertains to new or reman module, used module is just what you get and is non programmable)
Edit: The manual says it should work with the OBD I connector:
SECTION VI
TROUBLESHOOTING
2005 Tech 2 User’s Guide VI – 15
IMPORTANT
If not properly grounded, the CANdi module will appear to be defective when it is not. The Professional Diagnostic Tool CANdi module will fail due to improper grounding if you use the 16-pin DLC (J-1962) connector and power the
Tech 2 from an AC/DC power supply. The adapter you use must have a GM part number. Although PVI
adapters are similar to GM adapters, they will not work with the CANdi module.
CANdi Module Troubleshooting Guide
If a CANdi module is not functioning properly, please perform the following tests:
Make sure the CANdi module is properly grounded by connecting to a vehicle or by using the 12-pin
ALDL connector, which has the signal and chassis ground shorted.
loading..

Obdstar X300 DP Plus Help Files Megane IV Card Key & Blade Key Program

Look here: How to read flash + add new blade/card keys to Renault Megane IV 2015-
All done with OBDSTAR X300 DP PLUS and OBDSTAR P001 and OBDSTAR Renault adapter
Part 1: Obdstar X300DP Plus Help Files
Megane IV Blade Key
Megane IV key card
Part 2: X300DP Plus Test Report
Megane IV Add key card
Megane IV using Obdstar key master
Obdstar Help Files: Megane IV Blade Key
Select Diag Program in OBDSTAR X300 DP PLUS

Select software: Immobilizer – Renault – Renault 30.57 software


Select a function: Program keys

Select the model: Megane 2015-


Select the key type: blade key

Tip: Pls connect the OBDII -16 and P001 Renault converter at the same time;
otherwise, it would fail to make a dealer key

This function is available by connecting the server.
Pls ensure the internet connection is normal

Obdstar read car info

Vehicle model: Megane
Year: 2015-
Chip type: PCF7961
Remote frequency: 433 Mhz
Pin code: No need pin code
Working key required: No

Pictures:



Tips:
Menu description:
Read flash: read flash data in the immo ecu
Generate a dealer key: make a dedicated key that can be used for programming
Program keys: key learning for existing or new keys
Notice:
pls connect the OBDII -16 and converter at the same time; otherwise, it would fail to make a dealer key



Obdstar X300DP PLUS Help Files: Megane IV Card Key
Select the key type: card key

Tip: Pls connect the OBDII -16 and converter at the same time;
otherwise, it would fail to make a dealer key

This function is available by connecting the server.
Pls ensure the internet connection is normal

Obdstar read car info

Vehicle model: Megane
Year: 2015-
Chip type: PCF7961
Remote frequency: 433 Mhz
Pin code: No need pin code
Working key required: No

Pictures:



Tips:
Menu description:
Read flash: read flash data in the immo ecu
Generate a dealer key: make a dedicated key that can be used for programming
Program keys: key learning for existing or new keys
Notice:
pls connect the OBDII -16 and converter at the same time; otherwise, it would fail to make a dealer key
when performing the function of “generate dealer key”, pls place the key as shown in the figure



Remote:
Automatic
    Obdstar key master dp add new keys to Megane IV
Step 1: select a car model and key









Step 2: read flash





Step 3: program keys
Obdstar key master starts to program new keys

Open the emergency flasher


Select flash data

Switch ignition off

Hold the key you want to program on the Start/Stop button

Program a card key successfully!

The same method to program the next one


Learn complete

Step 4: test the new keys
Both new keys work good


Done!