BMW ICOM A2+B+C for BMW with 2018.9V Software program Plus EVG7 Diagnostic Tool FAQ

Query:
Can BMW ICOM A2+B+C software be updated if yes how so? And does this tablet run ista/d and ista/p can it program and code modules
Answer:
Hello my friend: the software could be updated, but you might want to obtain a new application HDD from us! You simply need to buy one particular time for one particular year, the software program is about USD 135 with shipping cost, it truly is one 500GB HDD, and this can be a specialist tester for BMW, so it could plan!
The update each year obtainable at our shop. Tablet run windows, so very same as typical laptop hardware.
Question:
Are you able to send me all the information and facts around the bmw laptop or computer is it just like ista when programing
Answer:
It may test and programmer,we have set up all software inside the EVG7, as well as active it properly, you'll be able to use it straight if you get it!
Query:
Is this wireless? Is every little thing already loaded onto the evg7? Thinking of purchasing BMW ICOM or a single with all the laptop which will be superior? Thanks
Answer:
hello my pal:
I hope you might have a very good day! we'll set up almost everything for you personally nicely just before we send it to you, you may choose the products as outlined by your need, if you can install the application by oneself, you can acquire it devoid of computer, just with one protable challenging disk with it, so you could use it with any laptop, for those who think install the software program is actually a dilemma, so you can pick the one together with the EVG7, we'll set up computer software for you, it can be ok?

Autel Tools Comparison List

Autel Tools Comparison List

How to Enable Immo and Programming in Consult 3 plus

Here is how to use Nissan Consult 3 Plus to do Immo and programming without spending out on the smart card.
find the consult diagnostictool.ini file
open with notepad
copy and paste this at the bottom
——————————————————–
[mode]
debug_mode=TRUE
debug_mode_vehicle-battery=TRUE
[vehicles]
tab_index=0
———————————————————
ALSO, MAKE SURE ACCESS_MODE IS SET TO 1 IN THIS FILE
NOW SAVE AND REOPEN CONSULT…VOILA!!!!!
Here is the location of fille DIAGNOSTICTOOL.INI:
C:\CONSULT-III_plus\System\Application\ApplicationData\CommonSetting\DiagnosticTool.ini
Please just try this at your own risk, I am not responsible the result if you have any question.
I share this because you can do this without spending money to buy the security card.
And this solution is for Car Scanner consult 3 plus.
If you can’t solve this problem, better buy consult 3 plus+ security card for IMMO AND PROGRAMMING.

What if the MDI error LED is on

1.What if the MDI error LED is on?
Power cycle the MDI. If error light stays on, perform a software recovery procedure. After the software recovery procedure has been executed, the GM MDI Scan Tool should pass the POST and the error LED should be off. If the MDI error LED is still on contact your customer support center. The MDI must be connected using USB and the latest version of MDI firmware must be installed before usage.
2.What if the MDI does not power up?
The MDI automatically powers up when power is applied to the DLC or the AC adapter, the MDI will not power up on battery power alone. If the MDI was powered down manually then the MDI will need to be powered up manually by pressing the ON/OFF button.
?Power MDI from an external source, AC 12-volt adapter or MDI DLC cable.
?Check cable connectors and power sources.
?Press ON/OFF button on the MDI.
3.Why does the MDI sometimes take longer
than 1 minute to complete POST (Power On Self Test)?
The MDI will take approximately 1 minute to complete POST the first time it powers ON following a firmware update.
4. Why does the MDI beep when power is lost?
This beep indicates the MDI AAA batteries are temporarily supplying power to the unit. If power is removed from the MDI, there will be an audible beep for approximately 30 seconds before the MDI powers down. The AAA battery life can be extended by manually powering the MDI down.
5.Why does the MDI turn off immediately when external power is lost?
If the AAA batteries have been installed and are charged, the MDI should remain powered up when external power is removed for up to 30 seconds. The amount of time the MDI remains powered depends on the strength of the batteries.
?Verify AAA batteries have been installed correctly.
?Replace AAA batteries.
6.Which version of MDI Manager software is on the PC? The MDI?
On the MDI Manager Explorer screen, select ‘Show Details’. The software version information is displayed for the currently selected MDI. The ‘Help’ tab will also show software version info (PC only if not connected to an MDI from www.obd2tool.com).